- You do not have any products in your shopping cart yet.
UV Nail Polish Gel Set + UV Dual Lamp Sun 9s - Pink
Starter set with LED/DUAL lamp Sun 9s pink
Contents:
- 1x LED/DUAL lamp SUN9s pink
- 2x LED UV gel polish - colors are chosen at random.
- 1x UV Base Gel Polish 6ml
- 1x UV/LED Quick Finish Gel 6ml
- 1x cleaner 100ml
- 1x Soak Off Remover 100ml
- 1x nail oil (scent may vary - random)
- 1x 250 celllets
- 1x buffer filing block
- 1x file straight - 100/180 grit
- 10x rosewood sticks
LED/DUAL lamp SUN9s pink
The lamp is made of light plastic and is also suitable for travel due to its compact dimensions.
- Hardens UV and LED gel, as well as UV/LED varnish, hybrid varnish and Shellac.
- With a light barrier that is activated by sensors and thus switches the device on and off.
- Without a base plate and therefore also very suitable for foot modelling.
- 24 watts
- Large LED screen for time display.
- No timer function - after 99s the device switches off automatically
LED/UV nail polish
Danger! This is a highly pigmented nail polish that needs to be applied very thinly to fully cure! If the color lifts off easily, it has been applied too thickly.
Note: For this high-quality nail polish you need our LED/UV Base & Top Vanish Lacquer, as well as the Soak Off Remover.
- The LED/UV gel based nail polish comes in a handy brush bottle.
- Is applied to UV gel or acrylic modeling like a conventional nail polish.
- Can also be used on the natural nail without nail modelling.
- Can be cured in an LED/UV combination device or in a UV device.
- Hard-wearing, does not splinter and is significantly more durable than conventional nail polish
curing time:
UV/LED combination device: 60 seconds
UV device : 120 seconds
Remove UV nail polish:
Put a celllet moistened with the Soak Off Remover on the nail for about 7 minutes. You can then easily lift and remove the nail polish with a rosewood stick.
UV Base Gellack 6ml - Base Coat - UV Gel Varnish
UV-Base Gel Varnish is a special UV primer varnish. The practical brush bottle makes application easy. Base Clear Coat is used for the primer of our colored UV/LED Gel Coats. The UV Base Gellack is equally suitable for natural nails, gel nails and toenails.
Quick finish gel
High-quality top coat for sealing the nail modellage. Fully cures under UV in 120 seconds, under UV/LED in 60 seconds and does not develop a sweating layer.
Cleaner / degreaser
To remove the layer of fat, the layer of sweat and to clean the modeling, e.g. of filing dust.
Remover
Special liquid for easy detachment and removal of LED/UV nail polish, hybrid polish.
nail oil
For the care of artificial nails, natural nails and cuticles.
250 celllets
The lint-free celllets are ideal for cleaning and degreasing the natural nail. For removing the layer of sweat, as well as for cleaning and disinfecting.
buffers
For removing fine to medium bumps.
Grit: 100
nail file
100/180 grit fine and coarse filing work
rosewood sticks
High-quality natural wood for gently cleaning and pushing back the cuticles. For nail modeling, manicures and pedicures.
Before you start with your first nail modelling, you should set up your workplace so that you have all the utensils to hand. Provide sufficient lighting at your workplace, possibly with an additional work lamp. UV light curing device, UV gels, files, buffers, cells, tip box, tip glue, cutter, brush, cleaner, dust brush, nail oil and possibly all nail art products such as stamp sets, glitter powder, rhinestones, etc. should be ready.
Instructions for remodeling
Instructions for french nail tips
Apply a thin layer of your chosen French or color gel to the tip of the nail (it doesn't have to be opaque yet) and cure for 15-20 seconds. Now the second layer of French or color is applied, creating a beautiful white or colored French tip. Please do not remove the sweat layer but continue working from step 14.
natural nail reinforcement
If you don't want to lengthen your fingernails (without nail tips) but only strengthen them, then step 5-8 can be omitted. Proceed with all further steps as described.
Filling in the nail modelling
When filling in gel nails, first file the transition of the mature gel nail flat and remove any lift, then carefully file any color, french or pattern, then continue from step 9.
Hints
UV gels must always be cured in a UV light curing device. Between the different work steps, always make sure that the gel jars are not standing directly on the light-curing device, otherwise they will harden in the jar. Make sure that no sunlight shines into the rooms or onto the workplace. Furthermore, you should not work outdoors.
Instructions for remodeling
- Wash hands thoroughly and dry well before starting. Remove nails from nail polish if necessary.
- Use a spatula or rosewood stick (broad side, not the tip) to gently loosen and push back cuticles.
- Shorten fingernails with a file and file them into an oval shape (natural nails should be shortened so that a maximum of 2mm protrudes).
- Roughen the natural nail carefully with a file or with a buffer until there is no more shine on the nail. Remove all dust from the nail with a nail brush or dusting brush. Please note that you no longer touch the roughened nail with your bare fingers.
- Determine tip size. Please note that the tip notch fits exactly on the natural nail. The tips should line up exactly with the sides of the nail. It is better to use a larger tip and file it slightly narrower on the sides than a tip that is too small.
- Now stick on the tip with the tip glue. Apply tip glue to the tip notch.
- Note: Then hold the tip down so that the tip adhesive does not run over the entire tip or onto your fingers. The tip must now be placed with the notch on the fingernail in such a way that the notch ends directly with the natural nail. Make sure that no air bubbles form under the tip adhesive surface. If this happens, please carefully file the tip off again. (possibly use a tip remover)
- Determine the length of the nails and use the cutter to shorten the tips and file them into the desired shape.
- File and roughen the tip carefully until it is no longer shiny. File the transition from tip support and natural nail until it is no longer visible. Then remove all dust from the nail with a nail brush or dust brush. Again, please ensure that you no longer touch the roughened nail with your fingers.
- The next step is to use the primer. Please apply primer sparingly to the natural nail and allow to dry briefly. Please make sure that the primer does not get on the cuticles.
- Now the 1st layer is applied (use UV adhesive gel or UV 1-phase gel)
- Apply a thin layer of UV primer gel or 1-phase gel to the entire nail with the gel brush. Please make sure that nothing runs into the edge of the nail. If gel has run into the edge of the nail, carefully remove the gel with a rosewood stick (pointed side). For beginners it makes sense to only apply gel to one finger at a time and then cure briefly in the UV/LED light curing device and then repeat finger by finger. When all fingers are done, please cure completely for 2 minutes. Now repeat the second hand step by step. Important: Do not remove the sweat layer! For French tips, please read the instructions for "French nails"
- After curing, the second layer is applied with the UV building gel or 1-phase gel. Put a small amount directly into the middle of the nail with the gel brush and spread it without applying pressure with the gel brush so that you achieve a beautifully curved nail shape. The highest point should be in the middle of the nail. Please make sure that nothing runs into the edge of the nail. Here, too, it makes sense for beginners to only apply gel to one finger at a time and then briefly cure it in the LED/UV light curing device and then repeat finger by finger. When all fingers are done, please cure completely for 1 to 2 minutes.
- Now carefully remove the sweat layer! Now moisten a cellette with cleaner and carefully wipe off the layer of sweat that has formed so that there is no longer a sticky spot. Now repeat the second hand step by step.
- Now file the nail plate with the file (fine-grain side) and smooth out any unevenness so that the desired nail shape is created. Then matt the nail with the buffer and remove filing marks. The nail must no longer shine.
- Now apply the sealing gel to the third and last layer. Apply the sealing gel thinly from the edge of the nail bed to the tip of the nail. Please make sure that nothing runs into the edge of the nail. Here, too, it is advisable for beginners to work finger by finger individually. Then completely harden all fingers for 2 minutes.
- Here, too, a layer of sweat develops, which should also be carefully removed.
- Now check the nails on the sides for gel residues and file them away carefully if necessary.
- Apply some nail oil to the cuticles and massage in.
Instructions for french nail tips
Apply a thin layer of your chosen French or color gel to the tip of the nail (it doesn't have to be opaque yet) and cure for 15-20 seconds. Now the second layer of French or color is applied, creating a beautiful white or colored French tip. Please do not remove the sweat layer but continue working from step 14.
natural nail reinforcement
If you don't want to lengthen your fingernails (without nail tips) but only strengthen them, then step 5-8 can be omitted. Proceed with all further steps as described.
Filling in the nail modelling
When filling in gel nails, first file the transition of the mature gel nail flat and remove any lift, then carefully file any color, french or pattern, then continue from step 9.
Hints
UV gels must always be cured in a UV light curing device. Between the different work steps, always make sure that the gel jars are not standing directly on the light-curing device, otherwise they will harden in the jar. Make sure that no sunlight shines into the rooms or onto the workplace. Furthermore, you should not work outdoors.
