UV Gel Starter Set - PHASE ONE - Nail Set

• 1x UV-LED combo device, model and color may vary
• 1x 1-phase gel 30ml
• 1x cleaner 100ml
• 1x buffer
• 3x narrow file, grain 100x180
• 2x banana file, grain 100x180
• 1x nail glue 3g
• 5x rosewood sticks
• 1x tips 100 pieces
• 1x brush set 3 pieces
• 1x cellettes (50 pieces)
• 1x cutter
• 1x primer 
• 1x practice finger
• 1x small Dust brush
• 2x nail art stickers (random, no selection possible)
• 1x nail art rondel (random, no selection possible)
• 1x nail art net (random, no selection possible)
• 1x step-by-step instructions

Before you start your first nail modeling, you should set up your workstation so that you have all the utensils to hand. Make sure that your workstation is adequately lit, possibly with an additional work light. UV light curing device, UV gels, files, buffers, tissue paper, tip box, tip glue, cutter, brush, cleaner, dust brush, nail oil and possibly all nail art products such as stamp set, glitter powder, rhinestones, etc. should be ready.

Instructions for new modeling  

1. Wash your hands thoroughly and dry them well before you begin. Remove any nail polish from your nails if necessary.
2. Carefully loosen and push back the cuticles using a spatula or rosewood stick (wide side, not the tip).
3. Shorten your fingernails with a file and file them into an oval shape (the natural nail should be shortened so that a maximum of 2mm protrudes).
4. Carefully roughen the natural nail with a file or buffer until the nail is no longer shiny. Remove all dust from the nail with a nail brush or dust brush. Please make sure that you do not touch the roughened nail with your bare fingers.
5. Determine the tip size. Please make sure that the tip notch fits exactly on the natural nail. The tips should line up exactly with the sides of the nail. It is better to use a larger tip and file it a little narrower on the sides than a tip that is too small.
6. .Now stick the tip on with the tip glue. Apply tip glue to the tip notch.
7. Note: Hold the tip downwards so that the tip glue does not run over the whole tip or onto your fingers. The tip must now be placed on the fingernail with the notch so that the notch is directly flush with the natural nail. Make sure that no air bubbles form under the tip adhesive surface. If this happens, please carefully file the tip off again. (Use a tip remover if necessary)
8. Determine the length of the nails and use the cutter to shorten the tips and file them into the desired shape.
9. Carefully file and roughen the tip until it no longer shines. File the transition between the tip pad and the natural nail until it is no longer visible. Then remove all dust from the nail with a nail brush or dust brush. Again, please make sure that you do not touch the roughened nail with your fingers.
10. The next step is to use the primer. Please apply primer sparingly to the natural nail and allow to dry briefly. Please ensure that the primer does not come into contact with the cuticle.
11. Now apply the first layer (use UV adhesive gel or UV 1-phase gel)
12. Apply UV primer gel or 1-phase gel thinly to the entire nail using the gel brush. Please ensure that nothing runs onto the edge of the nail. If gel does run onto the edge of the nail, carefully remove the gel from the edge using a rosewood stick (pointed side). For beginners, it is a good idea to only apply gel to one finger at a time and then cure briefly in the UV/LED light curing device and then repeat finger by finger. When all fingers are finished, please cure completely for 2 minutes. Now repeat the second hand step by step. Important: Do not remove the sweaty layer! For French tips, please read the instructions for “French nails”
13. After hardening, apply the second layer of UV builder gel or 1-phase gel. Use the gel brush to put a small amount directly in the middle of the nail and spread it with the gel brush without applying pressure so that you achieve a beautifully curved nail shape. The highest point should be in the middle of the nail. Please make sure that nothing runs onto the edge of the nail. Here, too, it is a good idea for beginners to only apply gel to one finger at a time and then harden it briefly in the LED/UV light curing device and then repeat finger by finger. When all fingers are finished, please harden completely for 1 to 2 minutes.
14. Now carefully remove the sweaty layer! Now moisten a tissue with cleaner and carefully wipe off the sweaty layer that has formed so that no sticky spots remain. Now repeat the second hand step by step.
15. Now file the nail plate with the file (fine-grained side) and correct any unevenness so that the desired nail shape is achieved. Then use the buffer to mattify the nail and remove any filing marks. The nail should no longer be shiny.
16. For the third and final layer, apply the sealing gel. Apply the sealing gel thinly from the edge of the nail bed to the tip of the nail. Please make sure that nothing runs into the edge of the nail. Here too, it is recommended for beginners to work on each finger individually. Then harden all fingers completely for 2 minutes.
17. Here too, a sweat layer forms, which should also be carefully removed.
18. Now check the nails on the sides for gel residue and carefully file it away if necessary.
19. .Apply some nail oil to the cuticles and massage in.

Instructions for French nail tips
Apply a thin layer of the selected French or color gel to the nail tip (it does not have to be opaque yet) and harden it for 15-20 seconds. Now the second French or color layer is applied so that a beautiful white or colored French tip is created. Please do not remove the sweat layer but continue working from step 14.

Natural nail reinforcement
If you do not want to lengthen your fingernails (without nail tips) but only strengthen them, then steps 5-8 are not necessary. All other steps are carried out as described.

Filling the nail modeling
When filling the gel nails, the transition of the fully grown gel nail must first be filed flat and any lifting removed, then all color, French or pattern must be carefully filed off and then work continues from step 9.

Notes
UV gels must always be cured in a UV light curing device. Between the different work steps, always make sure that the gel pots are not directly next to the light curing device, otherwise they will harden in the pot. Make sure that no sunlight shines into the rooms or on the workplace. Furthermore, you should not work outdoors.

UV 1-Phase Gel
Bis-HEMA Polyneopentyl Glycol Adipate/IPDI Copolymer, Bis-HEA Polyglycol Adipate/IPDI Copolymer, Trimethylolpropane Trimethacrylate (TMPTMA), Tripropylene Glycol Acrylate, Epoxy Methacrylate Oligomer, Acrylated Amine Synergist, 1,6 Hexanediol Diacrylate, Benzoyl Isopropanol, Glycol Dimethacrylate, Hydroxycyclohexyl Phenyl Ketone, CI 60725, CI 74160.

Cleaner / Degreaser
Isopropropyl Alcohol, Aqua.

Tip glue
Ethyl-2-cyanoacrylate

Primer
Ethyl acetate, isopropylidenediphenyl bisoxyhydroxypropyl methacrylate, HEMA, hydroquinone methyl ether / mequinol (P-hydroxyanisole)

Warnings
Keep out of reach of children! If it comes into contact with eyes, rinse thoroughly with water and seek medical attention. If skin redness or allergic reactions occur, discontinue contact with the product and seek medical attention if necessary. Avoid skin contact. May cause allergies.

• Please read the instructions for use carefully! 
• Use: For application to artificial fingernails. 
• For commercial use only!
• Country of manufacture Germany